Optimize and Improve Your Engineering Designs
Improving Your COMSOL Multiphysics Models
The Optimization Module is an add-on package that you can use in conjunction with any existing COMSOL Multiphysics Product. Once you have created a COMSOL Multiphysics model of your product or process, you always want to improve on your design. This involves four steps. First, you define your objective function – a figure of merit that describes your system. Second, you define a set of design variables – the inputs to the model that you would like to change. Third, you define a set of constraints, bounds on your design variables, or operating conditions that need to be satisfied. Last, you use the Optimization Module to improve your design by changing the design variables, while satisfying your constraints. The Optimization Module is a general interface for defining objective functions, specifying design variables, and setting up these constraints. Any model input, whether it be geometric dimensions, part shapes, material properties, or material distribution, can be treated as a design variable, and any model output can be used to define the objective function. It can be used throughout the COMSOL Multiphysics product family and can be combined with the LiveLink™ add-on products to optimize a geometric dimension in a third-party CAD program.
- OPTIMIZATION OF A FLYWHEEL: The optimization of the hole sizes of a flywheel is completed with the objective of minimizing the mass of the wheel. The hole sizes are the design variables and there is a constraint on the peak stress. As the hole sizes change, the location of peak stress occurs at different points. The derivative-free method is used to solve this optimization problem.
- SHAPE OPTIMIZATION OF A HORN ANTENNA: An initially straight-sided acoustic horn is optimized to improve the far-field sound pressure level. Shape optimization is used to arrive at the undulating corrugations of the horn.
- A TESLA MICROVALVE: The material distribution inside of a microfluidic device is adjusted to minimize the pressure drop if the fluid flows from left to right, and to maximize the pressure drop if the fluid flow is reversed.
- CURVE FITTING OF A HYPERELASTIC MATERIAL MODEL: Curve fitting (parameter estimation) of two parameters that define a nonlinear Mooney-Rivlin material model in solid mechanics to measured data.
- CHEMICAL REACTORS: A chemical solution is pumped through a catalytic reactor where a solute species reacts in contact with the catalyst surface. The model aims to maximize the total reaction rate of the solute for a given total pressure difference across the bed by finding an optimal catalyst distribution. Shown is the catalyst distribution (as the height), direction of flow (streamlines), and concentration distribution (color plot).
Derivative-Free and Gradient-Based Algorithms
The Optimization Module includes two different optimization techniques: Derivative-Free and Gradient-Based optimization. Derivative-Free optimization is useful when your objective functions and constraints may be discontinuous and do not have analytic derivatives. For example, you may want to minimize the peak stress in your part by changing the dimensions. However, as the dimensions change, the location of the peak stresses can shift from one point to another. Such an objective function is non-analytic and requires a derivative-free approach. Four such methods are available in the Optimization Module: the Bound Optimization by Quadratic Approximation (BOBYQA), Nelder-Mead, coordinate search, and Monte Carlo methods.
The Optimization Module will compute an approximate gradient to evolve the design variables towards an improved design. You may want to minimize the total mass of your part which can also be done using this approach. The mass of the part is usually directly differentiable with respect to the part dimensions, permitting use of a gradient-based approach. The Optimization Module will compute the exact analytic derivative of your objective and constraint functions using the adjoint method of the SNOPT optimizer, developed by Philip E. Gill of the University of California San Diego and Walter Murray and Michael A. Saunders of Stanford University, to improve the design variables. A second gradient-based algorithm is a Levenberg-Marquardt solver. You can use this solver when the objective function is of a least-squares type, typically for parameter estimation and curve fitting applications. A third method, the Method of Moving Asymptotes (MMA), is a gradient-based optimization solver written by Professor K. Svanberg at the Royal Institute of Technology in Stockholm, Sweden. It is designed with topology optimization in mind. The method is called GCMMA in the literature and is available in the Optimization Module under the name MMA.
The advantage of the gradient-based method is that it can address problems involving hundreds, or even thousands, of design variables with very low increase in computational cost as the number of design variables increases. The Adjoint method simultaneously computes all analytic derivatives, whereas the derivative-free method has to approximate each derivative, and will take more time as the number of design variables increases. The gradient-based methods can also include more complex constraint functions.
The advantage of the derivative-free method is in its simplicity. It does not require finding a differentiable objective function, and it requires less user interaction to set up. However, due to the computational costs, derivative-free methods are most attractive when the number of design variables is around 10 or less. In practice, this covers a wide range of practical engineering optimization problems.
Parameter Optimization involves optimizing any scalar input to the model, such as flow rates and load magnitudes. This is usually the easiest kind of optimization and can be addressed with any technique.
Parameter Estimation is more complex, and involves correlating a COMSOL model to experimental data. Typically, the objective is to use a model to estimate material properties used.
Dimension, Shape, and Topology Optimization
Optimization methods can be further classified by the types of variables being optimized. Dimension, Shape, and Topology optimization are all addressed within the Optimization Module, and each has its own place in the design process.
Dimensional optimization involves defining design variables that can be directly translated to manufacturing. Typical design variables may be hole sizes, or length, width, and height of structural members. Dimensional optimization is usually used as the last step in the design process and is performed once the design is more or less fixed in terms of the overall shape. The derivative-free method is usually used here.
Shape optimization typically occurs earlier in the design process, and involves a more free-form alteration of the object. More care is usually required for choosing the design variables, as the objective is to improve the shape without over-constraining the design. The gradient-based method is preferred if an analytic objective function can be found.
Topology optimization is used very early in the design process, typically in the conceptual stage. Topology optimization treats the distribution of material as a design variable and inserts or removes structures to improve the objective function. Due to the high number of design variables, only gradient-based optimization is practical.
Numerical Simulation-Based Topology Optimization Leads to Better Cooling of Electronic Components in Toyota Hybrid Vehicles
Toyota Research Institute of North America, MI, USA
The Toyota Research Institute in Ann Arbor drives cutting-edge research in energy efficiency, mobility infrastructure, and safety. Here, Ercan Dede and his team are designing heat sinks (or cold plates), which are affixed to fragile electrical systems and other applications in Toyota’s hybrid vehicles. Their simulations simulate the cold ...
Curve fitting material model data to experimental data
This presentation shows how to use the Optimization Module to fit a material model curve to experimental data. It is based on the hyperelastic Mooney-Rivlin material model example given in the Structural Mechanics users guide.
A demonstration of topology optimization using the Structural Mechanics Module and the Optimization Module. Three classical models are shown, the loaded knee, the Michell truss structure, and MBB beam. The optimization method is based on using the SIMPS approach to recast the original combinatorial optimization problem into a continuous ...
Topology Optimization of a Loaded Knee Structure
Imagine that you are designing a light-weight mountain bike frame that should fit in a box of a certain size and should weigh no more than 8 kg. Given that you know the loads on the bike, you can achieve this by distributing the available material while making sure that the stiffness of the frame is at a maximum. This way you have formulated the ...
Tuning Fork: Computing the Eigenfrequency and Eigenmode
This model simulates a tuning fork for tuning musical instruments which, if correctly designed, should sound the note of A, 440 Hz. It computes the fundamental eigenfrequency and eigenmode for the tuning fork. Although the example seems to be somewhat academic in nature, the eigenfrequencies and eigenmodes of microscopic tuning forks are also used ...
One way to fasten a gear to a shaft is by thermal interference. In preparation of the assembly, the shaft diameter is oversized and the gear thermally expanded in a heat-treating oven. At an appropriate expansion state, the gear is removed from the oven, slid onto the shaft, and allowed to cool. As the gear temperature drops, the gear shrinks and ...
Optimizing a Flywheel Profile
The radial stress component in an axially symmetric and homogeneous flywheel of constant thickness exhibits a sharp peak near the inner radius. From there, it decreases monotonously until it reaches zero at the flywheel’s outer rim. The uneven stress distribution reveals a design that does not make optimal use of the material available. Given ...
Minimizing the Flow Velocity in a Microchannel
Topology optimization of the Navier-Stokes equations is encountered in different branches and applications, such as in the design of ventilation systems for cars. A common technique applicable to such problems is to let the distribution of porous material vary continuously. In this model, the objective is to find the optimal distribution of a ...
Transient Optimization: Fitting Material Properties of a Wall
This model demonstrates transient optimization through the least squares solver. The model consists of a wall in 1D. The outer temperature varies over 24 hours and during this time, the inner temperature on the wall has been measured. This measured data is then used to fit the material properties (thermal conductivity and heat capacity at ...