C. Siegel, G. Bandlamudi, N. van der Schoot, and A. Heinzel
Zentrum für BrennstoffzellenTechnik GmbH, Duisburg, Germany
Institut für Energie- und Umweltverfahrenstechnik, University of Duisburg-Essen, Duisburg, Germany
Accurate bipolar-plate and flow-field layout is one crucial task for optimizing fuel cells. These cell components perform several functions, including charge transport or gas and water transport throughout the cell just to name a few. Overall, the design depends on the fuel cell application or the geometrical size of the assembly. The requirements for a flow-field used in a high temperature ...
M. Baù, V. Ferrari, and D. Marioli
Department of Electronics for Automation, University of Brescia, Brescia, Italy
A contactless electromagnetic principle for the excitation of mechanical vibrations in resonant structures has been investigated. The principle relies on no specific magnetic property of the resonator except electrical conductivity and can be adopted for employing the structures as resonant sensors for measurements either in environments not compliant with the requirements of active electronics ...
B.P. Cahill, M. Quade, G. Gastrock, K. Lemke, J. Metze, and D. Beckmann
Institut für Bioprozess und Analysenmesstechnik e.V., Rosenhof, Heilbad Heiligenstadt, Germany
This paper presents a simulation of the operation of a new type of droplet generation probe. This probe, consisting of two concentrically-arranged tubings, is immersed in a beaker of cell medium so that oil is pumped through the outer tubing at a pumping speed less than fluid is drawn into the inner tubing. In this way, droplets of cell medium are entrained into the outlet tubing forming a ...
P. Cendula, S. Kiravittaya, J. Gabel, and O.G. Schmidt
Institute for Integrative Nanosciences, Dresden, Germany
Strained wrinkled and flat nanomembranes have different bending properties when they are released from the underlying substrate. This is caused by increased bending rigidity of the wrinkled film in one direction. We provide theoretical and numerical analysis of the directional rolling of wrinkled films, which is important for positioning rolled-up tubes on the short mesa edge during fabrication.
F. Bircher and P. Marmet
Institute of Print Technology, Bern University of Applied Sciences, Burgdorf, Switzerland
Electromagnetic micro valves are currently developed empirically or the different physics are treated separately. To accelerate the development-process and for a better understanding of the overall system, a multiphysics simulation is built up. This simulation considers the electromagnetics, the electronics (including the control of the process), the mechanics and the fluidics with respect to the ...
Dipartimento di Energetica “Sergio Stecco”, Università degli Studi di Firenze, Firenze, Italy
Energy performances and building energy quality can be achieved by high performance envelopes. In this paper the thermal performance of a naturally ventilated façade, applied to a traditional wall, widely used in existing buildings, was investigated by a transient simulation. A three dimensional model of the façade was investigated in Florence and Treviso (Italy). The simulation ...
N. Delmonte, M. Bernardoni, P. Cova, and R. Menozzi
Dipartimento di Ingegneria dell’Informazione, University of Parma, Parma, Italy
This work describes a way to apply 3D Finite Element Analysis (FEA) to the thermal design of power electronic modules using simplified geometry models of the system components. The method here presented can overcome the problem of solving equation systems with a very high number of Degrees Of Freedom (DOF) due to complex geometry of a power module.
Simulation of the Convective Heat Transfer and Working Temperature Field of a Photovoltaic Module Using COMSOL Multiphysics®
E. Ruiz-Reina and M. Sidrach-de-Cardona
Departamento de Física Aplicada II, Universidad de Málaga, Málaga, Spain
The aim of this work is the Finite Element Analysis (FEA), by using COMSOL Multiphysics®, of the convective heat transfer and working temperature field of a photovoltaic module under different wind conditions.
S. Thomas, P.Y. Franck, and P. André
Department of Sciences and Environmental Management, University of Liège, Arlon, Belgium
This paper presents the heat flow model and the experimental test bench developed to optimize a new kind of heating floor. In the first part of the text is described the new kind of high reactivity emitting device for building heating and cooling. The second part illustrates the numerical model developed to evaluate the device efficiency. Finally experimental test bench implementation and ...