Technical Papers and Presentations

Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Modelling of the Wool Textile Finishing Processes

M. Giansetti[1], A. Pezzin[1], S. Sicardi[1], G. Rovero[1]
[1]Politecnico di Torino, Torino, Italy

Within wool textile industries, a very important role is played by the so-called finishing processes, in which the textile substrate undergoes steam treatments to achieve the desired level of stabilisation and appearance. Process parameters, namely temperature and moisture content, are known only at the beginning of the process but not in the textile material being treated, where the actual ...

Helical Coil Flow: A Case Study

M. Cozzini[1]

[1]Renewable Energies and Environmental Technologies Research Unit, Fondazione Bruno Kessler, Povo, TN, Italy

Stationary flow configurations in curved pipes constitute an important subject from both the theoretical and the practical point of view. A typical application concerns the calculation of secondary flow effects on the thermal efficiency of heat exchangers. Motivated by a similar problem, this paper investigates the flow patterns in a helical duct of non trivial cross section. The considered ...

Fluid Flow in Porous Ceramic Multichannel Crossflow Filter Modules

G. Breitbach, S. Alexopoulos, and B. Hoffschmidt
FH Aachen, Jülich, Germany

In this work, we show how the modeling of purification of fluids can be simplified using a combination of analytical and numerical methods. A basic cell is defined based on the periodic structure of the module-cross section. The cell represents the microstructure of the cross section. Considering the cell, flow related effective quantities are derived. The finite element method is here used only ...

Numerical Modelling of Vortex Induced Vibrations  in Submarine Pipelines

F. Van den Abeele, J. Vande Voorde, and P. Goes
ArcelorMittal Research & Development Industry Gent, Zelzate, Belgium

Vortex-induced vibration is a major cause of fatigue failure in submarine oil and gas pipelines and steel catenary risers. Even moderate currents can induce vortex shedding. In this paper, COMSOL Multiphysics is applied to study the flow pattern around submarine pipeline spans, and predict the amplitude and frequency of the vortex induced vibrations. The sensitivity of the computational fluid ...

Assessing the Potential of Ventilated Facades on Reducing a Buildings’ Thermal Load Using Decoupled COMSOL Simulations

J. van Schijndel[1], C. van Dronkelaar[1]
[1]Eindhoven University of Technology, Eindhoven, The Netherlands

Solar radiation is a prominent contributor of energy in buildings, and can be transmitted directly into a building through opaque surfaces, but it can also be absorbed by building components (i.e. walls, roofs etc.). This study discusses the use and effect of ventilated facades, with an external facade cladding, a sub-structure anchored to the wall surface of the building under solar radiation, ...

Modeling Void Drainage with Thin Film Dynamics

J.J. Gangloff Jr.[1], W.R. Hwang[2], S.G. Advani[1]
[1]Center for Composite Materials, Department of Mechanical Engineering, University of Delaware, Newark, DE, USA
[2]School of Mechanical Engineering, Gyeongsang National University, Jinju, Gyeongsangnam-do, Korea

Voids in composite materials can lead to degraded structural performance. The following is a study of voids or bubbles in uncured viscous polymer resin during composites processing. The goal is to determine if voids can successfully migrate towards vacuum pathways, coalesce with the pathways, and escape. Inherent to the coalescence process is the drainage and rupture of the resin thin film formed ...

On the Use of COMSOL Multiphysics to Understand and Optimize the Filling Phase in the Injection and Micro-Injection Molding Process

M. Moguedet1, P. Namy2, and Y. Béreaux3
1Pôle Européen de Plasturgie, Bellignat, France
2SIMTEC, Grenoble, France
3LAMCOS, Site de Plasturgie, INSA Lyon, Bellignat, France

The work presented here deals with the simulation of the cavity filling stage of the injection and micro-injection molding process for thermoplastic materials.COMSOL Multiphysics gives us the means to take into consideration some other aspects usually neglected in commercial 3D softwares dedicated to polymer processing. In particular, tracking of the flow front is based on a Level Set approach. ...

Numerical Simulations of Thixotropic Fluids

P. Dantan[1], and M. Faye[2]
[1] Université Paris7 Denis Diderot
[2] Université Paris11

In this paper, we introduce a kinetic equation coupled with the Navier-Stokes equations in COMSOL Multiphysics in order to simulate internal structural changes of a flowing complex fluid. Two physical applications are considered, the starting of blood flow in a stenosis and a simulation of a laboratory rheometric set-up. Results show good agreement with the experiments' well known ...

Numerical Simulation of an Induction Stirred Ladle

M. Pal1, S. Kholmatov2 and P. Jönsson2
1Centre-University of Wales, Swansea
2Royal Institute of Technology, Stockholm, Sweden

In this paper a simulation model of a laboratory scaled induction ladle is presented. The simulation model so developed will make it feasible to receive information about the fluid flow phenomenon and thermal heat transfer. In order to perform the numerical simulation of the furnace, physical processes involved are expressed as a coupled-nonlinear system of partial differential equations ...

Analysis of Lubricant Flow Through Reynolds Equation

K.C. Koppenhoefer[1], S.Y. Yushanov[1], L.T. Gritter[1], J.S. Crompton[1], and R.O. Edwards[2]
[1]AltaSim Technologies LLC, Columbus, OH, USA
[2]Cummins Fuel Systems, Columbus, IN, USA

Reynolds equation is used to analyze fluid flow through small gaps. As such, the solution of Reynolds equation provides critical information for a wide range of tribological problems. In any case where a lubricant resides between two moving surfaces, the Reynolds equation can be used to solve for the flow. In the case considered in this paper, lubricant flows between a piston and housing forced ...

Quick Search