L. Armellin, F. Gatelli, and G. Tanghetti
R&D Department, Metelli S.p.A., Cologne, BS, Italy
Ball joints are widely used in many applications. This paper describes the contact and kinematic analysis of an Rzeppa type constant-velocity joint (CV-joint). Starting from a conveniently simplified 3D model, at fixed joint angle of 45°, a CV-joint made of all “generic steel” components has been studied. Considering only a “perfect” geometry (i.e. not affected by ...
R. C. Thiagarajan, and K. V. Chiranjeevi
ATOA Scientific Technologies Private Limited
The predictive engineering of materials is matured from predicting properties from known morphology or constituents to engineering novel morphology for superior properties. The focus of this paper is about implementation of computational material mechanics modeling method in COMSOL Multiphysics software for engineering the constituents for superior properties. A brief review of property ...
VLSI Layout Based Design Optimization of a Piezoresistive MEMS Pressure Sensors using COMSOL Multiphysics
R. Komaragiri, Sarath. S., N. Kattabomman
NIT Calicut, Kozhikode, Kerala
This paper focuses on the diaphragm design and optimization of a piezoresistive Micro Electro Mechanical System (MEMS) pressure sensor by considering Very Large Scale Integration (VLSI) layout schemes. The aim of these studies is to find an optimal diaphragm shape by Finite Element Method (FEM) using COMSOL®, which is most suitable for VLSI layout. Optimal diaphragm shape is a diaphragm shape ...
E. Isaza, E. Salazar, L. Florez
Universidad Tecnológica de Pereira, Pereira, Risaralda, Colombia
The consequences of hip fracture and femoral fracture are widely known. The mechanical strength of the femur varies in every person, but it is possible to predict the mechanical resistance with parameters like density, dimensions and mineral content. This paper uses different models and empirical studies to determine the mechanical properties of the human femur, developing isotropic and ...
F. Van den Abeele, and P. Goes
ArcelorMittal Research and Development, Ghent, Belgium
When an enamelled steel part is cooled down after firing, residual stresses are induced due to the difference in thermal dilatation between the enamel and the steel grade. At room temperature, the steel substrate is under tensile stress state, while the enamel is under compression. The thermal stress distribution can be measured with a Klotz test device. Here, a cantilever steel/enamel sample is ...
Z. Hasan, F. Darwish, and S. Al-Absi
Texas A&M University, College Station, TX, USA
Jordan University of Science and Technology, Irbid, Jordan
The main objective of the present work is to perform stress analysis on composite laminates under unaxial/biaxial loading to serve as a preliminary data for test verification. A detailed calculation based on the Classical Lamination Theory was performed for a laminate. The material used was carbon/epoxy applying a pure uniaxial load followed by a biaxial load. It was observed that the failure ...
N. Elabbasi, J. Bergstrom, and S. Brown
Veryst Engineering, LLC.
Peristaltic pumping is an inherently nonlinear multiphysics problem where the deformation of the tube and the pumped fluid are strongly coupled. We used COMSOL Multiphysics to investigate the performance of a 180 degree rotary peristaltic pump with two metallic rollers, and an elastomeric tube pumping a viscous Newtonian fluid. The model captures the peristaltic flow, the flow fluctuations ...
Time-Dependent Thermal Stress and Distortion Analysis During Additive Layer Manufacturing, by Powder Consolidation by Laser Heating
M.S. Yeoman, J. Sidhu
1. Continuum Blue Ltd., Tredomen Innovation & Technology Park, Tredomen, Ystrad Mynach, United Kingdom
BAE Systems, Advanced Technology Centre, Bristol, United Kingdom
A time-dependent COMSOL Multiphysics model of an additive manufacture process, which uses powder consolidation by laser heating was developed, providing a platform to better understanding the manufacture process & provide a tool to reduce resulting distortion & optimization of an additive manufacture process. The model simulates a high intense laser energy source moving along a pre-defined time ...
Design and Nuclear-Safety Related Simulations of Bare-Pellet Test Irradiations for the Production of Pu-238 in the High Flux Isotope Reactor Using COMSOL
J.D. Freels, P.K. Jain, R.W. Hobbs
Oak Ridge National Laboratory, Oak Ridge, TN, USA
The Oak Ridge National Laboratory (ORNL) is developing technology to re-establish the capability to produce plutonium-238 for the National Aeronautics and Space Administration (NASA) as a power source material for powering vehicles while in deep-space. The High Flux Isotope Reactor (HFIR) of ORNL has been utilized to perform test irradiations of in-capsulated neptunium oxide (NpO2) and aluminum ...
C. Thiagarajan, G. Shenoy, B. S. Shenoy
ATOA Scientific Technologies Pvt Ltd, Whitefield, Bangalore, India.
Department of Mechanical & Manufacturing Engineering, Manipal Institute of technology, Manipal, India
Department of Aeronautical & Automobile Engineering, Manipal Institute of Technology, Manipal, India
Vibration and Dynamic performances of the rotating machinery are conventionally evaluated based on the dominant structural forces such as the centrifugal forces. The increase in rotational speed, miniaturization and performance, demands for improved and accurate evaluation of the vibration performance. The inclusion of coupled effects of fluid and centrifugal forces can contribute significantly ...